Sheild Your Pavers With Top Ideas On How To Seal Paver Blocks

Paver blocks are the right materials that add a touch of elegance to your outdoor patio projects, be it a walkway, paver driveway, or garden patio. But, just like keeping anything nice, pavers need a little bit of care like paver sealing to keep it beautiful for longer. 

Thus, as the top paver blocks manufacturers in Kolkata, we will show you the ways how to seal paver blocks in this blog. 

Recommended: How Block Paving Colours Can Enhance Driveways - Top Colours

Why Sealing Paver Blocks Is Important?

As paver blocks are absorbent, several problems might arise if the pavers are not sealed properly. During the installation process, your main aim is to interlock the pavers with sand for integrity. 

But, that is not enough for the long run. Using paver sealers comes in handy to keep your paver surface clean under any climatic weather. Therefore, helping you to keep the pavers and sand intact while minimizing weed growth on the surfaces. 

So, as the best manhole covers manufacturer, we have an array of paver blocks, manhole covers, and FRP covers in Kolkata. They are not just durable but are value for money. And, that is why, knowing how to seal paver blocks properly needs all your attention. 

What Are The Materials Needed For Sealing Paver Blocks?

Sealing your concrete pavers is not a hard task, however, there are a few materials and tools that you must keep with yourself throughout the entire process. They are -

• Safety Gloves
• Brush or Broom
• Pressure Washer
• Type Of Sealer/ Patio Joint
• Sealing Kit
• Sealer Coats
• Joining Sand. 

An Easy Guide: How To Seal Paver Blocks?

Step 1: Sweep And Clean

Start by brushing off the existing dirt, debris, and other sealers from the surface of the brick paver to make it clean and dry. 

This will help you to prepare the surface for the step by step process of sealing pavers. You can also use a sprayer to clean the area clean.

Step 2: Deep Clean With Pressure Washer

Once, you are done with sweeping the surface of your paver blocks. It is time for you to give your paver joints and surface a deep cleaning to pull out hard stains and dirt. 

Thus, use pressure wash to clean your pavers before sealing as paver sealant works best in dry conditions. 

Step 3: Dry The Surface Of The Pavers

After pressure washing, you must leave the paver areas to dry out completely. Give your pavers at least two weeks to dry before moving ahead with the sealing concrete pavers process. 

Step 4: Refill The Joints With Sand

Check whether your outdoor hardscapes need a coat of joint sand before the sealing process or not. It is recommended to reapply a layer of joining sand on the paver's edges and joints as it must have washed out during the cleaning process.

Thus, apply a thick sand layer on your paver driveway or patio and swipe the excess sand out. 

Step 5: Select The Type Of Sealer

Choose a high-quality sealer to penetrate through your paver blocks to give them a natural look. The first coat of sealer is usually poor. That is why, you must reapply a good amount of sealant again after the first coat dries out.

Step 6: Apply The First Coat Of Sealant

Before you start applying a layer of sealant on your unsealed pavers, make sure to follow the safety guidelines and take necessary precautions to avoid any hassles.

Use a roller to apply the sealant throughout the entire area for sufficient coverage. It is best if you can use a thick layer of sealant for best results. Leave the area to dry for 1 to 2 hours before applying the second coat.

Step 7: Use A Sprayer For The Second Coat

Spray a thin layer of sealer over the first coat of the sealed pavers appropriately for extra protection and durability. It is important to seal the sealer with a nice coat to make the area look more natural.

Step 8: Give Time To Cure

Allow the sealer to settle on your paver patio for at least 24 hours to 48 hours for final effects. The curing time is important so that the sealer gets locked into the paver blocks for longevity.

Read More: Om Concrete Uses New Technologies In Paver Block Production

Conclusion

Knowing how to seal paver blocks is an investment that pays off, isn't it? 😉 Sealing your pavers is not really a difficult task, just needs a little bit of practice to keep them looking fresh and aesthetic for the longest time. 

You can also check out our range of paver blocks that are customizable on our website.